EMT Practice Test

1. Question Content...

Previous Submit Next
Was this helpful? Upvote!
Question List

Question1: Atechnicianwants to upgradethe iDRAC licensefromExpress to Enterprise.
What are the three methods thetechniciancanuseto install the newlicense?(Choosethree.)

Question2: Which three steps must a technician take prior to replacing a server component with blue tabs/release? (Choose three.)

Question3: A technician needs to deploy a server into production. The technician needs to verify that the firmware levels match corporate policy before putting the server on the business network.
Which two methods should the technician use to verify the firmware version of iDRAC and BIOS? (Choose two.)

Question4: What are two requirements for using the iDRACS Quick Sync feature? (Choose two.)

Question5: A technician needs to add a device to SupportAssist for Servers. Policy requires that NO additional software be installed on the server OS.
What information is required to add the device?

Question6: A technician needs to configure a server to allow the OS to manipulate processor frequencies for higher power efficiency.
How should the technician perform this task?

Question7: A technician has a server with the following memory configuration:
*Sixteen 4 GB dual-rank DIMMs
*48 GB available to the OS
The workload intended for the server required the memory configuration to protect against some errors. Now the technician must deploy for a different workload that requires access to all available memory.
Which setting should the technician change to make all memory available to the system?

Question8: A technician needsto set a server to always attempt PXE boot beforebooting to the harddrive.
What two itemsdoes thetechnicianneed to set to achieve this? (Choose two.)

Question9: A technician is sent on-site to troubleshoot a server that reports errors during POST when rebooted. The LCD is amber. The error message is as shown:
correctable memory error rate exceeded for DIMM B4
The server has a limited maintenance window. The technician needs to troubleshoot efficiently.
Which step should the technician take to troubleshoot?

Question10: A technician needs to troubleshoot a server. The OS was operational. After an untrained person accesses the System Setup utility on the server, the OS now fails to load.
The technician reboots the server, selects F2, accesses the System Setup utility, and selects System BIOS.
The technician needs to verify items in the System BIOS settings before reloading the OS.
Which two items should the technician verify? (Choose two.)

Question11: A technician needs to configure a server to PXE boot a server setup image with the BIOS in UEFI mode.
Which two steps should the technician perform to enable this function? (Choose two.)

Question12: A technician has a 13G system that is giving NO video to a crash cart connected to the front VGA port. The LCD is NOT reporting any errors. The system reports 'CPU Resetting' messages sporadically in the lifecycle log. The iDRAC runs an Express license.
The technician needs to most efficiently determine if the system is completing POST despite the video issue.
Which two steps should the technician take to perform this task? (Choose two.)

Question13: A technician installs a server with a network daughter card (NDC). The NDC has two 10Gb BaseT ports as well as 1Gb BaseT ports. The technician is using the correct CAT-6 network cable and a 10Gb switch.
The server reports 1Gb connections on ports 3 and 4. Ports 1 and 2 are down.
How should the technician get 10Gb connectivity?

Question14: A server has two power supply units (PSUs) in a redundant configuration. One power supply unit fails.
A technician replaces the failed PSU, but the server does NOT return to redundant power mode.
What is the cause of this issue?

Question15: How can a system administrator compare the currently installed hardware to the original system configuration?

Question16: A system admin needs to create a new iDRAC use that should NOT have privileges to change any iDRAC features or ability to configure additional users.
Which user configuration options will meet these criteria?

Question17: A technician needs to roll back the firmware on a server for the Fiber Channel card. The technician needs to determine the previous version before rolling back the firmware.
How should the technician view the previous and current firmware versions utilizing Lifecycle Controller?

Question18: A PowerEdge server is running a hypervisor. The server must be configured to enable multiple virtual machines to share the PCIs hardware resources of a supported NIC.
Which System BIOS setting must be enabled to provide this functionality?

Question19: A technician deploys a server. The iDRAC was configured with a static IP address and hostname.
The technician can NOT ping the iDRAC from the workstation when using the hostname.
The technician can ping the iDRAC with the IP address.
Which setting should the technician configure to fix the deployment?

Question20: A server has two 1100w power supplies. The system needs to enable or disable power supplies dynamically depending on power needs. Power Supply 2 needs to be main power supply.
Which two settings should the technician change? (Choose two.)

Question21: An existing server is transferred to a new location. When the iDRAC port is plugged into the network, it causes an IP conflict.
The technician is directed to change iDRAC settings via the LCD Front Panel Display.
There is NO option to make changes.
What is the most probable cause of this issue?

Question22: A technician needs to replace a server component with orange tabs/releases.
Which two steps should the technician take to complete this task? (Choose two.)

Question23: A technician configures iDRAC on a new server for access on the management network.
When accessing via telnet, the connection is refused. Network connectivity is a verified network. NO ports are blocked by any network devices.
Why is the telnet connection being refused?